JCD3006
MOBILE CD PLAYER / RECEIVER
Installation and Operation Manual
JCD3006
JCD3006
7. After completing the wiring connections, attach the front panel and turn the unit on to
confirm operation (vehicle ignition switch must be on). If the unit does not operate,
recheck all wiring until the problem is corrected. Once proper operation is achieved, turn
the ignition switch off and proceed with final mounting of the chassis.
8. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is
fully seated and the spring clips lock it into place.
INSTALLATION
Before You Begin
1. Disconnect Battery
Before you begin, always disconnect the battery negative terminal.
2. Remove Transport Screws
9. Attach one end of the
Important Notes
perforated support strap
Dashboard
(supplied) to the screw stud on
the rear of the chassis using
the hex nut and spring washer
provided. Fasten the other end
of the perforated strap to a
secure part of the dashboard
either above or below the radio
using the screw and plain
washer provided. Bend the
strap, as necessary, to position
it. CAUTION: The rear of the
radio must be supported with
the strap to prevent damage to
the dashboard from the weight
•
•
•
•
•
•
•
Before final installation, test the wiring connections to make sure the unit is connected
properly and the system works.
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications to your vehicle.
Install the unit where it does not interfere with driving and cannot injure passengers if
there is a sudden or emergency stop.
If the installation angle exceeds 30º from horizontal, the unit might not give optimum
performance.
Avoid installing the unit where it will be subject to high temperatures from direct sunlight,
hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.
Be sure to remove the control panel before installing the unit.
Support Strap
Screw Stud
Plain Washer
Screw (5 x 25mm)
Hex Nut (5mm)
Spring Washer
DIN Front/Rear Mount
of the radio or improper operation due to vibration.
This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear”
(DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis)
mount. For details, refer to installation methods A and B.
10. Re-attach the front panel to the chassis and test radio operation by referring to the
operating instructions for the unit.
Removing the Unit
DIN Front Mount (Method A)
1. Remove the detachable front panel, if it is
To remove the radio after installation:
Dashboard
Dashboard
1. Insert fingers into the groove in the front of
frame and pull out to remove the frame.
(When re-attaching the frame, point the
side with a groove downwards and re-
attach.)
2. Insert the removal keys straight back until
they click, and then pull the radio out. If
removal keys are inserted at an angle,
they will not lock properly to release the
unit.
attached to the chassis, by pushing the
REL button.
Bend Tabs
Screw Stud
182
2. Slide the mounting sleeve off of the
chassis if it has not already been removed.
If it is locked into position, use the removal
keys (supplied) to disengage it. The
removal keys are depicted in “Removing
the Unit” on page 3.
3. Check the dashboard opening size by
sliding the mounting sleeve into it. If the
opening is not large enough, carefully cut
53
Removal Key
Trim Plate Installation
Push the trim plate against the chassis until it is
fitted. You must do this before you install the
control panel, otherwise it can't be attached.
or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve
into the opening or cause it to bend or bow. Check that there will be sufficient space
behind the dashboard for the radio chassis.
4. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.
With the sleeve fully inserted into the dashboard opening, bend as many of the tabs
outward as necessary to firmly secure the sleeve to the dashboard.
5. Place the radio in front of the dashboard opening so the wiring can be brought through the
mounting sleeve.
DIN Rear Mount (Method B)
This unit has threaded holes in the chassis side panels which may be used with the original
factory mounting brackets of some vehicles to mount the radio to the dashboard. Please
consult with your local mobile stereo shop for assistance on this type of installation.
1. Remove the existing factory radio from the dashboard or center console mounting. Save
all hardware and brackets as they will be used to mount the new radio.
6. Follow the wiring diagram carefully and make certain all connections are secure and
insulated with crimp connectors or electrical tape to ensure proper operation.
3
JCD3006
2. Carefully unsnap the plastic trim ring from the front of the new radio chassis. Remove and
discard the trim ring.
3. Remove the factory mounting
brackets and hardware from
the existing radio and attach
them to the new radio. Select
a position where the screw
holes of the bracket and the
Screws
screw holes of the main unit
are aligned (are fitted).
Dashboard
Tighten the screws at 2
places on each side. Do not
exceed M5 x 9 MM maximum
screw size. Longer screws
Factory
Mounting
Bracket
may damage components
inside the chassis.
Hook (Remove)
4. Wire the new radio to the
vehicle as outlined in the Universal Installation instructions.
5. Mount the new radio assembly to the dashboard or center console using the reverse
procedure of step 1.
NOTE: The mounting box, outer trim ring, and half-sleeve are not used for method B
installation.
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
Detachable Control Panel (DCP)
Removing the Detachable Control Panel (DCP)
1. Turn the power off.
2. Press the REL button.
3. Remove the DCP.
PANEL RELEASE
Attaching the DCP
BUTTON
1. Attach the panel at the right side first, with point B on the
main unit touching point A on the DCP (as shown in the
2
diagram).
2. Press the left side of the DCP onto the main unit until a
“click” is heard.
A
CAUTION:
1
B
•
DO NOT insert the DCP from the left side. Doing so may
damage it.
•
The DCP can easily be damaged if dropped or
subjected to a strong shock. When the release button is pressed and the DCP is
unlocked, the vehicle's vibrations may cause it to fall. To prevent damage to the DCP,
always store it in a protective case after detaching it.
•
•
The rear connector that connects the main unit and the DCP is an extremely important
part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
If the DCP is dirty, remove debris with a soft, dry cloth only. You can use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the DCP.
4
JCD3006
WIRING
688A
ANTENNA
JACK
ANTENNA SOCKET
FUSE
20-PIN
AUDIO/POWER
HARNESS
(See Figure 1)
RCA-TO-RCA CABLE
(not supplied)
WHITE
RED
REAR LINE OUT
GREY
AMP
Figure 1: 20 PIN HARNESS PIN CHART
1
2
3
4
5
6
7
8
9
10
Power Antenna
Connect to power antenna or amplifier,
If not used, tape bare end of wire.
BLUE
11 12 13 14 15
16 17 18 19 20
BLACK
Ground
Connect to ground terminal or clean
unpainted metal part of chassis.
PIN
1
2
WIRE COLOR
GREY / BLACK
GREY
FUNCTION / LABEL
RIGHT FRONT SPEAKER (
RIGHT FRONT SPEAKER (+)
RIGHT REAR SPEAKER (+)
)
3
4
VIOLET
RIGHT REAR SPEAKER (
N/A
LEFT REAR SPEAKER (+)
)
VIOLET/BLACK
EMPTY
GREEN
YELLOW
Memory / Battery
5
Connect to battery or 12 volt power source
that is always live. The radio will not work if
this wire is not connected.
6
7
GREEN / BLACK
RED
BLACK
LEFT REAR SPEAKER (
IGNITION (ACC)
)
8
9
10
REAR PRE-AMPLIFIER LINE OUT COMMON
RIGHT REAR PRE-AMPLIFIER LINE OUT
LEFT FRONT SPEAKER (+)
RED
RED
Accessory / Ignition
Connect to existing radio wire or radio fuse.
11 WHITE
12
WHITE / BLACK
LEFT FRONT SPEAKER (
N/A
POWER ANTENNA
)
13 EMPTY
14 BLUE
15 YELLOW
BATTERY (+)
CHASSIS GROUND
16
BLACK
17 EMPTY
18 EMPTY
N/A
N/A
N/A
EMPTY
WHITE
19
20
LEFT FRONT
RIGHT FRONT
WHITE-BLACK LF-
GREY-BLACK RF-
LEFT REAR PRE-AMPLIFIER LINE OUT
GREY RF+
WHITE LF+
RIGHT REAR
LEFT REAR
GREEN-BLACK LR-
VIOLET-BLACK RR-
VIOLET RR+
GREEN LR+
5
JCD3006
Display (D)
BASIC OPERATION
Press the D button (18) on the control panel (or the DISP button on the remote control) to view
the clock. The LCD will display the clock for 5 seconds, then return to the previous display
mode.
3
7
4
19
22
2
Clock Adjustment
With the clock displayed, press the D button (18) until the LCD flashes. Press the up >>| (21)
button to adjust the hours or the down |<< button (20) to adjust the minutes. (You can also use
the U and D buttons on the remote control to set the hour and minutes.)
JCD3006
Reset
After releasing the control panel, use a pencil or any non-metallic
object to press and hold the RESET button for five seconds to reset
the main unit. The unit will return to the factory default settings. The
reset button should be activated for the following reasons:
•
•
•
initial installation of the unit when all wiring is completed
function buttons do not operate
error symbol on the display
1
6
5
20
21
12 13 14 15 16 17
10
9
8
11
18
Control Panel Release (REL)
Press the REL button (3) to release the control panel.
NOTE: If after pressing the RESET button the unit still does not function normally, use a
cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control
panel.
4
S
1
6
Power On/Off ( )
Press the button (1) to turn the unit ON or OFF.
VOL
Audio Menu
VOL
Volume Control
To increase the volume, rotate the volume control
knob (6) clockwise.
Press the volume control button (4) on the control panel (or the S button on the remote control)
to access the Audio Menu. You can navigate through the Audio Menu items by pressing the
volume control button repeatedly, or by pressing the up >>| (21) or down |<< (20) buttons.
Once the desired menu item appears on the display, adjust that option by turning the volume
control knob within 5 seconds. The unit will automatically exit the Audio Menu after five
seconds of inactivity. The following menu items can be adjusted.
21
D
U
20
TR. UP
TR. DN
LOUD
10
5
19
9
BND
LOC
SCN
AMS
MOD
To decrease the volume, rotate the volume control
knob counter clockwise.
7
PEQ
11
18
14
13
17
8
When the volume is adjusted, the volume level is
shown on the display panel as a number ranging from
00 (lowest) to 100 (highest).
MO
PAU
MUT
SCN
DISP
RPT
23
12
Volume Level
1
2
5
3
6
Use the volume control knob to adjust the Volume level from “00” (lowest) to “100” (highest).
15
16
4
Bass Level
SHUF
Mute
Use the volume control knob to adjust the Bass level range from “-10” to “+10”.
Press the MUTE button (8) on the control panel (or the
MUT button on the remote control) to mute the audio
output. “Mute” will appear on the display. Press MUTE
again to restore the audio output to the previous level.
Treble Level
Use the volume control knob to adjust the Treble level range from “-10” to “+10”.
Balance
Use the volume control knob to adjust the Balance between the right and left speakers from
“R10” (full right) to “L10” (full left). “C00” represents an equal balance between the right and left
speakers.
Mode
Press the MODE button (5) on the control panel (or
the MOD button on the remote control) to select a
different mode of operation, as indicated on the
Fader
Use the volume control knob to adjust the Fader between the front and rear speakers from
“R10” (full rear) to “F10” (full front). “C00” represents an equal balance between the front and
rear speakers.
display panel. Available modes include Radio, CD, and AUX In (optional Auxiliary Input).
Auxiliary Input
1. Connect the external signal to the “Aux In” jack (22) located on the front of the control
panel.
2. Press the MODE button to select Aux In mode.
3. Press MODE again to cancel Aux In mode and return to previous mode.
6
JCD3006
Preset Stations
Six numbered preset buttons store and recall stations for each band.
TUNER OPERATION
3
7
4
19
22
2
Store a Station
Select a band (if needed), then select a station. Hold a preset button (12-17) for three seconds.
The preset number will appear in the display.
Recall a Station
Select a band (if needed). Press a preset button (12-17) to select the corresponding stored
station.
JCD3006
Automatically Store / Preset Scan (AS/PS, AMS)
Automatically Store
Select a band (if needed). Press AS/PS (11) on the control panel (or the AMS button on the
remote control) for more than three seconds to automatically select six strong stations and
store them in the current band. The new stations replace any stations already stored in that
band.
1
6
5
20
21
12 13 14 15 16 17
10
9
8
11
18
Preset Scan
Select a band (if needed). Press AS/PS (11) to scan stations stored in the current band. The
unit will pause for ten seconds at each preset station. Press AS/PS again to stop scanning
when the desired station is reached.
Select a Band
Press the B button (19) on the control panel (or the BND button on the remote control) to
change between three FM bands and one AM band. Each band stores up to six preset
stations.
Loudness Control (B, BND)
Press the B button (19) on the control panel (or the BND button on the remote control) to turn
the “Loudness” function on/off. When Loudness is activated, the display will show “X-Bas” for a
few seconds.
Tuning
Auto Seek Tuning
Press the up >>| (21) or down |<< button (20) on the control panel (or the U or D buttons on the
remote control) for less than three seconds to move to the next station automatically.
Preset Equalizer (PEQ)
Press the PEQ button (7) to select from the following preset equalizer functions: FLAT >
CLASSIC > POP M > ROCK > DSP OFF. When “DSP OFF” is selected, the EQ function is
controlled by the Bass/Treble settings.
Manual Tuning
Press the up >>| (21) or down |<< button (20) for more than three seconds to enter manual
tuning mode. Press the up >>| (21) or down |<< button to change the radio frequency number
up or down one step. The radio signal strength meter indicates the strength of the current radio
station broadcast.
Stereo
The unit will automatically pick up an FM stereo signal, when available. When in stereo mode,
the “ST” icon appears in the display. When no stereo signal is available, the unit will
automatically revert to mono operation, and no icon will be displayed. To manually switch
between mono and stereo mode, press the MO button (23) on the remote control.
Worst
Reception
Best
Reception
Scan
Press the SCN button (10) to automatically search for stations. Each available station will flash
on the display for a few seconds before the next is searched. To select a “flashing” station,
press the SCN button again.
Local/Distant (LO/DX)
During radio operation, received signals are usually in stereo mode as indicated by the “ST”
icon; however, when the signals are weak or intermittent, you can activate the Local (LOC)
mode by pressing the LO/DX button (9) (“LOCAL” appears on the display) on the control panel
(or the LOC button on the remote control). This mode favors access to local stations whose
signals are much stronger; thereby improving radio reception. Press the LOC button again to
terminate Local receive mode.
7
JCD3006
CD OPERATION
3
7
4
19
22
2
JCD3006
1
6
5
20
21
12 13 14 15 16 17
10
9
8
11
18
Insert and Eject Disc
Insert a disc, label-side up, with the unit turned on. “S-CDP” will display on the LCD for about 2
seconds and the unit will play the first track on the disc. Press the eject button (2) to stop disc
play and eject the disc. The unit does not have to be turned on to eject the disc.
Controlling Disc Playback
Track Select
Press the up >>| (21) or down |<< button (20) on the control panel (or the U or D buttons on the
remote control) for less than one second to advance to the next track on the CD. The selected
track number will appear on the display. Press and hold the up >>| (21) or down |<< button (20)
for >1 second to fast forward or fast reverse through the disc. CD play starts when the button is
released.
Play/Pause Disc Playback (1/PAU)
Press the 1/PAU button (12) to suspend disc play. Press the 1/PAU button again to resume
disc Play.
Intro Scan (2/INT)
Press the 2/INT button (13) on the control panel (or the 2/SCN button on the remote control) to
play the first 10 seconds of each track sequentially. Press 2/INT again to stop Intro Scan and
resume normal play at the current track.
Repeat Play (3/RPT)
Press the 3/RPT button (14) during disc play to repeat play the current track. Press 3/RPT
again to stop repeat play
Random Play (4/RDM)
Press the 4/RDM button (15) on the control panel (or the 4/SHUF button on the remote control)
during disc play to play all tracks on a CD in random, shuffled order. Press 4/RDM again to
stop random play.
8
JCD3006
SPECIFICATIONS
TROUBLESHOOTING
CD
Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 70dB
Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz
Quantization Bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 bit
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20,000Hz
Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Channel (Stereo)
Symptom
Cause
Solution
No power
The vehicle’s ignition is not If the power supply is properly
on
connected to the vehicle acces-
sory terminal, switch the ignition
key to “ACC”.
FM Radio
The fuse is blown
Replace the fuse.
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5-107.9MHz
Intermediate Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7MHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 15dB at S/N 30dB
Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25dB at 1KHz
S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB
Disc cannot be loaded or Presence of CD disc inside Remove the disc in the player and
ejected
the player
insert the new one.
Inserting the disc in reverse Insert the compact disc with the
direction
label facing upward.
Compact disc is extremely
dirty or disc is defective
Clean the disc or try to play a new
one.
AM/MW
Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530-1710KHz
Intermediate Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450KHz
Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 45dB
S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB
Temperature inside the
vehicle is too high
Wait until the ambient tempera-
ture returns to normal.
Condensation
Leave the player off for an hour or
so, then try again.
General
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 11 -14.4
Grounding System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative Ground
Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms
Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40W x 4
No sound
Volume is too low
Adjust volume to audible level.
Check wiring connections.
Wiring is not properly con-
nected.
The operation keys do
not work
Control panel not properly
installed
Reinstall control panel.
The built-in microcomputer
is not operating properly
due to noise
Press the RESET button.
Sound skips
The installation angle is
more than 30 degrees.
Adjust the installation angle to
less than 30 degrees.
The disc is dirty or defec-
tive.
Clean the disc and try to play
again or use new disc.
Cannot tune to radio sta- The antenna cable is not
Insert the antenna cable firmly.
tion, auto-seek does not
work
connected.
The signals are too weak.
Mechanism Error
Select a station manually.
ERROR 1
ERROR 2
Press the eject button to correct
the problem.
If the error code does not disap-
pear, consult your nearest ser-
vice dealer.
Servo Error
Press the eject button to correct
the problem.
If the error code does not disap-
pear, consult your nearest ser-
vice dealer.
9
JCD3006
ASA Electronics Corporation
© 2006 ASA Electronics Corporation
v.071206
10
|
Indesit Cooktop I6VV2A User Manual
Indesit Washer Dryer IWDE 12 User Manual
Indesit Washer Dryer WD 10 User Manual
Intex Recreation Marine Sanitation System CS8110 User Manual
Invacare Mobility Aid Transformer User Manual
JVC Flat Panel Television LT Z37EX6 User Manual
Kenwood MP3 Player HD20GA7 User Manual
KitchenAid Mixer KV25G0XBU4 User Manual
Konica Minolta All in One Printer A0HF012 User Manual
Korg Music Mixer EMX1 User Manual